Ok, 2s2n server is dead. fuck that. Let’s start the fucking theather

Man, all the manuals to build a satsuma gt in my summer car. that’s a fucking complex shit

Kids, this kills your brain cells
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.

.
.
.
.
.

.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
..
.
.
.
.
.
Engines:
Crankshaft snaps on to the Engine Block
Main Bearings 6x9mm
4 Pistons 8x7mm each
Head Gasket snaps to Engine Block
Cylinder Head – 10x7mm
Rocker Shaft – 5x8mm
Camshaft – 2x5mm (Goes in a hole located on the “left” side of engine.)
Camshaft Gear – 1x10mm
Timing Chain snaps on to Camshaft Gear
Timing Cover – 6x6mm
Water pump – 5x7mm
Crankshaft Pulley – 1x11mm
Waterpump Pulley – 4x7mm
Distributor – 1x6mm
Alternator – 1x7mm 1x10mm, 1x10mm, 1x Screwdriver (Tighten Screw after Fan Belt)
Fan Belt snaps to Pulleys and Alternator. Doesn’t need to be removed from package.
Engine Plate
Starter – 2x7mm
Carburator – 4x8mm
Headers (Exhaust Manifold) – 5x8mm
Flywheel – 6x7mm
Clutch Disk to Clutch Cover Plate
Clutch Pressure Plate to Clutch Disk
Clutch Assembly – 6x6mm
Oil Pan – 8x7mm, 1x13mm
Gearbox – 6x7mm, 1x10mm
Drive gear – 7x6mm
Spark Plugs 1,2,3 and 4 – Use the Spark Plug Socket located in the toolbox
Rocker Cover – 6x7mm
Fuel Pump – 2x7mm
Air Filter – 2x6mm
Oil filter – Tightens by hand (scroll up, similar to the gas caps)
Attach the Engine to the engine hoist. Lower the hoist, set the engine on the ground. Try to line up the 2x10mm bolts somewhat close and tighten them. Hopefully the engine will “jump” into place.

Chasis and stuffs:
Sub-frame – 4x10mm – bottom of engine bay
Steering Rack – 4x9mm – bottom of engine bay, drivers side near back of the engine bay.
Steering Column – 2x8mm – goes from interior of vehicle to steering rack
Wishbones – 2x10mm each – near each wheel well towards bottom of engine bay
Spindles – 1x12mm each – on end of wishbones
Steering Rods – 1x12mm each – connect from wheel wells. (NOTE: install the struts before tightening bolts!)
Disc Brakes – 1x14mm each – install in wheel wells NOTE: connect Half-shafts before you tighten
Half-shafts – 3x9mm each that connect to the gearbox once installed- 1x14mm each (Bolt Shared with Disc Brake)
Struts – 4x9mm each, 3x10mm each, 1x12mm each (12mm Bolt Shared with Steering Rods.) Install vertically between each fender and the steering rod.
Trailing Arms – 2x12mm each – rear of vehicle inside wheel wells.
Coil Springs – snap into place – vertically between rear fender and trailing arm.
Shock absorbers – 1x12mm, 2x6mm each – vertically near coil springs
Drum Brakes – 1x14mm each – on end of trailing arm
Wheels – 4x13mm each – on drum brake
At this point many of the parts will be easier to find the install location if you mount the Engine.
Hubcaps – snap on to wheels – not necessary if you don’t want them.
Battery – snaps in near fender inside engine bay, front passenger side
Electrics – 2x8mm to the body – position blue wires near spark plugs and hope :(.
Fuel strainer – 1x8mm – passenger side fender inside engine bay, can be tricky…..

(too long that the other parts havem’t been here)

Well, Finland repairs cars.

@milktea I’ve assigned you to renamed your profile name into FTLRalph. You’ll be in the “Players that will be banned” part. I’ll give my username and go find it: JuryGamer2005

and help me to find a village. If you want, make a simple prison to be used for “banned users” part. The mode is “creative” so we can find a village and build sets easily.

@datsmoothanimator you\’re a good animator and a good fig maker even though you\’re young